Payment & Shipping Terms:
|Type:||Welded Mesh||Wire Gauge:||3.5mm|
|Material:||Hot Dipped Galvanized Wire||Hole:||50x50mm,50x100mm, 75x75mm|
|Hole Shape:||Square||Application:||Cpnstruction Cages|
2x2 inch ,3.0mm Wire Thickness Galvanized Welded Wire Mesh Gabion Box Sold Well In Middle East
Material: Low-Carbon Iron Wire,Galvanized Iron Wire
Wire Diameter: 3-6 mm,such as 3.5 mm,4 mm,5 mm,6 mm
Zinc Coated: 200-300 g/㎡
Surface Treatment: hot dip galvanzed after welded
Stiffener length: 300 mm
Spiral Binder wire diameter: 3.7 mm etc.
Mesh Hole: 5 x 5 cm,5 x 10 cm,7.5 x 7.5 cm,10 x 10 cm,10 x 20 cm
Box Size : 2 x 1 x 1 m, 2 x 1 x 0.5 m, 1 x 1 x 1 m, 1 x 1 x 0.5 m, 1 x 0.5 x 0.5 m, 0.3 x 0.3 x 0.3 m, as your
Product Specification List
|Feature||Skilled Welded by High Quality|
|Color||Dark Green;Light Green;Yellow|
|Length||10m---30m in roll|
|Treatment||Good Zinc Galvanized +PVC|
|Wire Diameter||6.0,8.0,10.0 mm|
|Packing||In Rolls or Sheets|
Y shape welded wire mesh fence,Welded wire mesh gabion basket for sale garden gabion,Welded wire mesh gabion basket /retaining wall for
sale garden gabion
1) Foundation preparation
The foundation on which the gabions are to be placed shall be cut or filled and graded as required.
Surface irregularities, loose material, vegetation, and all foreign matter shall be removed from foundation
surface area. Extra care should be taken with foundation preparations in order to ensure a level and
Rotate the gabion panels into position and join the vertical edges with fasteners for gabion assembly.
Where spiral fasteners are used, crimp the ends to secure the spirals in place. Where C ring type
alternate fasteners are used for basket assembly, install the fasteners at a maximum spacing of 150 mm.
Use the same fastening procedures to install interior diaphragms where they are required. Interior
diaphragms will be required where any inside dimension exceeds 1m for gabion baskets. Diaphragms will
be installed to assure that no open intervals are present that exceeds 1m.
Place the empty gabions on the foundation and interconnect the adjacent gabions along the top, bottom
, and vertical edges using spirals or C rings.
Gabion cages can be built in a modular method by eliminating an end panel for each cage so no two
panels need be connected together. The same method may also be used for successive courses including
lid and base panels. Interconnect each layer of gabions to the underlying layer of gabions along the front,
back, and sides.
Staking of the gabions may be done to maintain the established proper alignment prior to the placement of
rock. Connecting lacing wire and other fasteners shall be attached during the filling operation to preserve
the strength and shape of the structure.
Internal connecting cross-tile (stiffener) wires shall be placed in each unrestrained gabion cell, including
gabion cells left temporarily unrestrained. In welded mesh gabions these crossties or stiffeners will be
placed across the corners of the gabions providing diagonal bracing. Lacing wire or preformed wire
stiffeners may be used.
The gabions shall be carefully filled with rock, ensuring alignment, avoiding bulges, and providing a
compact mass that minimizes voids.
The last layer of rock shall be uniformly leveled to the top edges of the gabions. Lids shall be placed over
the rock filling using only approved lid closing tools as necessary. The use of crowbars or other single
point leverage bars for lid closing is prohibited due to the potential for damage to the baskets. The gabion
lid shall then be secured to the sides, ends, and diaphragms with spiral binders, approved alternate
fasteners, or lacing wire wrapped with alternating single and double halfhitches in the mesh openings.
Contact Person: AmandaRen